Braco Brass Single Compression Cable Glands are suitable for armoured /unarmoured cables. These are manufactured out of brass castings and are machined accurately to the required sizes.
These glands are nickel plated to avoid corrosion while storage and use. Each gland comprises of Brass Body with nipple thread as per I.S. 12943:1990.
Compression nut , Check nut, Rubber Ring and three metal washers .
The detail parts are shown in the functional drawing.
Braco cable glands are weather proof and water tight and have provision for earthing the armoured cables .These lands are available in various different sizes and are suitable for all cables upto 1000 sq .mm. and control cables upto 61 cores .\
The entry thread on gland body is normally threaded according to IS 1653(Steel conduits for electric wiring).
However if any special kind of thread required, the same can be supplied. The glands can be supplied with special plating such as cadmium,tin or passivated.
Single compression Braco Cable Gland Selection Chart Characteristics
Washers of soft metal will be provided for firm gripping of armour.
Earth tag will be provided if required at extra cost
PVC protective shrouds can be supplied at extra cost
Washers between rubber ring are supplied for uniform radial gripping.
Braco Single Compression Cable gland selection chart
O.D of cable should be less than D-3
Diameter of cable underneath the overall sheating for unarmoured cable and underneath the armouring for armoured cables is not more than D-34.
Selection of rubber ring is made such that the dia over armouring for armoured cables and dia underneath
The overall sheathing for unarmoured cable is less than rubber I.D. A-1.
Single Compression Braco Cable Gland Selection Chart:
Glands Ref. E
NIP. OD D-3
CAP. BORING D-3 A
NIP. ID D
A.CROSS. L-9
BODY HIGHT L-10
NIP. HIGHT M
B. NUT A-1
RUB. ID above
Cable diameter (mm)
BC-3/8″
1/2″
14
12
20
10.50
6
2
8
9 – 13.5
BC-1/2″L
5/8″
15
13
23
12.50
6.50
2
12
10 – 14.5
BC-1/2″H
5/8″
15
13
23.50
14
7.50
3
12
10 – 14.5
BC-5/8″L
3/4″
15
15
23
14
7
2
12
10 – 14.5
BC-5/8″H
3/4″
15
15
23.50
15
8
3
12
10 – 14.5
BC-3/4″L
3/4″
17.50
15
26
15.50
8
2.50
14
14 – 17
BC-3/4″H
3/4″
17.50
15
27.50
16.50
9
3
14
14 – 17
BC-7/8″L
3/4″
20
15
29
16
8
2.50
16
17 – 19.5
BC-7/8″H
3/4″
20
15
29.50
17
9
3
16
17 – 19.5
BC-1″L
1
23.50
21.50
32.50
17.50
8
3
20
19.5 – 23
BC-1″H
1
23.50
21
34.50
19
10
3.50
20
19.5 – 23
BC-1″S
3/4″
23.50
15
32.50
17.50
8
3
18
19.5 – 23
BC-1-1/8″
1-1/8″
28
25
39
21
10.50
4
25
23 – 27
BC-1-1/4″
1-1/4″
31.50
27
42.50
21
10.50
4
27
27 – 30
BC-1-3/8″
1-3/8″
35.50
31
47.50
22
10.50
4.50
31
30 – 34
BC-1-1/2″
1-1/2″
39
34
52
22
10.50
4.50
33
34 – 38
BC-1-3/4″
1-3/4″
45
40
59
23
11.50
4.50
39
38 – 44
BC-2″
2″
51.50
45
68
23
11.50
4.50
44
44 – 50
BC-2-1/4″
2-1/4″
58
52
75
23.50
11.50
5
52
50 – 56.5
BC-2-1/2″
2-1/2″
62.50
58
80
25
13
5.50
58
56.5 – 61
BC-2-3/4″
2-3/4″
70
65.50
90
28
13.50
5.50
65
61 – 68
BC-3″
3″
76
69.50
100
28
13.50
5.50
70
68 – 74
BC-3-1/4″
3-1/4″
82
75
15
29
15
5.50
75
74 – 80
BC-3-1/2″
3-1/2″
88
82
117
29
15
6
80
80 – 86
BC-4″
4″
100
92.50
127
36
20
6
86
86 – 98
BC-4-1/2″
4-1/2″
108
102
145
38
23
7
90
98 – 105
Image for Single Compression Braco Cable Gland Selection Chart:
Image for Single Compression Braco Cable Gland Selection Chart:
Image for Single Compression Braco Cable Gland Selection Chart
Double Compression Weatherproof Cable Glands
Braco Double Compression Cable Glands are manufactured out of brass rods/castings and are machined accurately to the required sizes. These are nickel plated to avoid corrosion whilst storage and use.
These DC glands have two moisture proof seals and may be used under most climatic conditions. These are weather proof and water proof and when protected by a PVC shroud, these can be used under most corrosive conditions. The armour cone and ring gives excellent mechanical and electrical connections.
These DC cable Glands are certified by Central Institute of Mining and Fuel Research, Dhanbad for use in weatherproof conditions. These Glands are rated with IP protection upto IP-65 Levels. These glands are as per BS 6121:Part 1:2005 and have parts: Brass body, Armour clamp and Ring, Gland Barrel sealing nut, two seals, , check nut and flat washer between the gland barrel and check nut is provided to prevent the drag on outer seal.
These DC cable glands are available in various different sizes and are suitable for all cables up to 1000sq. mm and control cables up to 61 cores. Threads can be ET / mm /NPT as per requirement. However if any special kind of gland or thread is required, the same can be supplied on request.
The gland can also be supplied with any other special plating such as cadmium, tin or passivated. Also the glands can be supplied made out of aluminum, mild steel or stainless steel.
Double Compression Brass Glands For Armoured Cable (Weatherproof) or WP DC cable gland
Braco Double Compression Glands are manufactured out of brass rods/castings and are machined accurately to the required sizes. These are nickel plated to avoid corrosion whilst storage and use. These glands have two moisture proof seals and may be used under most climatic conditions. These are weather proof and water proof and when protected by a PVC shroud, these can be used under most corrosive conditions. The armour cone and ring gives excellent mechanical and electrical connections.
These DC cable gland Glands are certified by Central Institute of Mining and Fuel Research, Dhanbad for use in weatherproof conditions. These DC Glands are rated with IP protection upto IP-65 Levels. These glands are as per BS 6121:Part 1:2005 and have parts: Brass body, Armour clamp and Ring, Gland Barrel sealing nut, two seals, , check nut and flat washer between the gland barrel and check nut is provided to prevent the drag on outer seal.
These glands are available in various different sizes and are suitable for all cables up to 1000sq. mm and control cables up to 61 cores. Threads can be ET / mm /NPT as per requirement. However if any special kind of gland or thread is required, the same can be supplied on request.The gland can also be supplied with any other special plating such as cadmium, tin or pasivated. Also the glands can be supplied made out of aluminum, mild steel or stainless steel
Braco Cable Gland Selection Chart Characteristics
Clamping cone will be provided with knurling for firm gripping of the armour.
Earthing tag will be provided if required at extra cost
PVC perotective shroud can be supplied at extra cost
Washers between seals are supplied for uniform radial gripping of PCP seals
Installation Instructions
Remove the outer sheath to the desired length depending on the lenght of the leads required and splay out the armour wire one by one and then cut the same according to the size of armour Clamping cone. File the sharp edges of the armour wire and for the gland as per assembly shown sectionally
Image for Double Compression Weatherproof Braco Cable Gland Selection Chart:
Image for Double Compression Weatherproof Braco Cable Gland Selection Chart:
Image for Double Compression Weatherproof Braco Cable Gland Selection Chart
Double Compression Brass Glands For Armoured Cable (Flame Proof) or FLP DC gland
Certified by : Central Institute of Mining & Fuel Research
Braco Double Compression Glands are manufactured out of brass rods/castings and are machined accurately to the required sizes. These are nickel plated to avoid corrosion whilst storage and use.
These glands have two moisture proof seals and may be used under most climatic conditions.
These are weather proof and water proof and when protected by a PVC shroud, these can be used under most corrosive conditions. The armour cone and ring gives excellent mechanical and electrical connections.
These Glands are certified by Central Institute of Mining and Fuel Research, Dhanbad for use in Flameproof and weatherproof conditions. These Glands are rated with IP protection upto IP-68 Levels.
These DC glands are as per BS 6121:Part 1:2005 and have parts: Brass body, Armour clamp and Ring, Gland Barrel sealing nut, two seals, check nut , check nut and flat washer between the gland barrel and check nut is provided to prevent the drag on outer seal.
These DC glands are available in various different sizes and are suitable for all cables up to 1000sq. mm and control cables up to 61 cores.
Threads can be ET / mm /NPT as per requirement. However if any special kind of gland or thread is required, the same can be supplied on request.
The DC cable gland can also be supplied with any other special plating such as cadmium, tin or pasivated. Also the glands can be supplied made out of aluminum, mild steel or stainless steel
Desciption of Flange Braco Cable Gland Selection Chart
Braco Flange Type Cable Glands are made out of brass castings and are machined accurately to the required sizes. These glands are suitable for armoured cables and are called mechanical glands hence suitable for outdoor application.
Parts of Flange Braco Cable Gland Selection Chart
The gland comprises of brass body (flange type oval shape) and plate clamped with galvanized mild steel studs and nuts for clamping the armour. Tapered cone and nut are provided for termination of cable. The cone and body taper is designed for giving a firm grip to the armour of the cable.
Braco flange glands as per customers needs and requirements. It is also called mechanical cable glands. These are mostly applicable for armored cable glands and outdoor use.
Characteristics of Flange Braco Cable Gland Selection Chart
Our high quality products provide longer service life, dimensional accuracy, strong grip and corrosion resistant, high compressive strength, excellent brass finish, with these excellent features these are available in different sizes and designs as per customers specifications to full fill all industrial standards..
These glands comprises of Flange type over shape brass body and plate secure with nuts and galvanised mild steel studs of clamping the shell and these nuts are use for termination of cable.
Link : BracoFlange Type Cable Glands
Flange Type Braco Cable Gland Selection Chart
Code No
E(mm)
Max Dia Of Cable
Under Armour Dia
L
Acceptance Dia
FL5
15
16.50
10
13
12 – 16.5
FL4
19
19
13.50
13
15 – 19
FL3
19.50
20.50
13
13
18.5 – 20.5
FL2
25
24.50
19
16.50
20.5 – 24.5
FL1
31
30
25.50
15.50
24 – 30
FL11
31
34
28
15
29.5 – 34
FL0
37.50
35
29.50
21
32.5 – 35
FL00
37.50
38
29.50
20
34.5 – 38
FL38
42
42
34.50
21.50
37 – 42
FL001
49
44
41
20.50
40.5 – 44
FL002
53.50
52
46
21.50
43.5 – 52
FL003
60
58
52
23
51 – 58
FL0033
65
67
56
25.50
56.5 – 67
FL004
75
76
65.20
22.50
66 – 76
FL005
99
83
88
22.50
75 – 83
Image for Flange Braco Cable Gland Selection Chart:
Image for Flange Braco Cable Gland Selection Chart:
Image for Flange Braco Cable Gland Selection Chart
Application
• Control panels, Switchgears, Transformers, Circuit breakers
• Electricity power generation and Distribution Industries
• Electronic Industries
• Railways
• Steel & Fertilizers Industries
• Cement & Textile Industries
• Mining Industries
• Sugar Industries
• Defense Industries
• Shipping Industries
• Aeronautic Industries
• Satellite & Communication Industries
• Automobile Industries
• Chemical Projects
• Domestics
Importance of Cable Gland selection chart
Cable gland is very essential for cable termination.
Different gland sizes are used on different types of cables.
But selecting the perfect cable gland for a particular cable is very difficult.
So, Cable Gland selection chart plays a very important role in selecting the most accurate error free cable gland.
Additional information
Description
Braco Cable Gland Selection Chart – Rujuta Corporation is dealer of Braco Lugs, single compression Brass Cable Glands and crimping tools are suitable for armoured / unarmoured cables.
Brand
Braco
Material
Brass, Copper & Aluminium
Product Code
Braco Cable Gland Selection Chart
Reviews
There are no reviews yet.
Be the first to review “Braco Cable Gland Selection Chart” Cancel reply
Download catalog
Reviews
There are no reviews yet.